If the output voltage range is exceeded the LED control gear reduces the LED output current. After elimination of the overload the nominal operation is restored automatically.
In case of a short circuit on the secondary side (LED) the LED control gear switches off. After elimination of the short circuit the nominal operation is restored
The LED control gear works in burst working mode to provide a constant output voltage regulation which allows the application to be able to work safely when LED string open due a failure.
In no-load operation the output voltage will not exceed the specified max. output voltage.
Humidity: 5% up to max.85%
not condensed (max.56 days/year at 85%)
Storage temperature: -40 °C up to max. +80 °C
The devices have to be within the specified temperature range (ta) before they can be operated.
|Type||ta||40 °C||50 °C||60 °C|
|LCBI 8W 180mA phase-cut SR VTX||tc||60 °C||70 °C||x|
|Life-time||40,000 h||30,000 h||x|
|Maximum Loading of Automatic Circuit Breakers|
|Automatic circuit breaker type||C10||C13||C16||C20||B10|
|Installation Ø||1.5 m㎡||1.5 m㎡||1.5 m㎡||2.5 m㎡||1.5 m㎡|
|LCBI 8W 180mA phase-cut SR VTX||60||90||120||140||30|
|Automatic circuit breaker type||B13||B16||B20|
|Installation Ø||1.5 m㎡||1.5 m㎡||2.5 m㎡||1max||Time|
|LCBI 8W 180mA phase-cut SR VTX||45||60||70||10 A||100 µs|
Replace LED module
1. Mains off
2. Remove LED module
3. Wait for 5 seconds
4. Connect LED module again
Hot plug-in or secondary switching of LEDs is not permitted and may cause a very high current to the LEDs.
Wiring type and cross section
The wiring can be in stranded wires with ferrules or solid. For perfect function of the cage clamp terminals the strip length should be 8 – 9 mm for the input terminal.The max. torque at the clamping screw (M3) is 0.2 Nm.
All connections must be kept as short as possible to ensure good EMI behaviour.
Mains leads should be kept apart from LED control gear and other leads (ideally 5 – 10 cm distance)
Max. lenght of output wires is 2 m.
Secondary switchting is not permitted.
Incorrect wiring can demage LED modules.
The wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.).
Tridonic Driver ODM for Vertex
Reliable quality, new design
Independent dimmable LED control gear
Output current 180 mA Constant current LED control gear
Max. output power 8 W
Nominal life-time up to 40,000 h
Dimmable via leading edge and trailing edge phase dimmers
Output dimmed analogue (current amplitude)
Dimming range typ. 10 to 100 % (depending on dimmer)
For luminaires of protection class I and protection class II
For luminaires with M and MM as per EN 60598, VDE 0710 and VDE 0711
Temperature protection as per EN 61347-2-13 C5e
Casing: polycarbonat, white
Type of protection IP20
Push-in terminals (input side)
No output current overshot at mains on/off(at full load)
|Rated supply voltage||220–240 V|
|Input voltage, AC||198–264 V|
|Typ. rated current (at 230 V, 50 Hz, full load)||0.05 A|
|Power factor at full load||0.9|
|Power factor at min. load||0.9|
|Mains frequency||50/60 Hz|
|Max. input power||11 W|
|Output power||6–8 W|
|THD (at 230 V, 50 Hz, full load)||<20 %|
|THD (at 230 V, 50 Hz, min. load)||<20 %|
|Output current tolerance (at 230 V, 50 Hz, full load)||±7.5 %|
|Output current tolerance (at 230 V, 50 Hz, min. load)||±10 %|
|Turn on time (at 230 V, 50 Hz, full load)||≤0.7 s|
|Turn off time ( at 230V,50Hz,full load)||≤0.7 s|
|Hold on time at power failure||0 s|
|Ambient temperature ta||-20...+50 °C|
|Max. casing temperature tc||70 °C|
|Storage temperature ts||-40 ... +80 °C|
|Dimensions L x W x H||128 x 41 x 25 mm|
|Specific Technical Data|
|Type||Output current||Effieciency at full load||Effieciency at min. load||Min. output voltage||Max. output voltage|
|LCBI 8W 180mA phase-cut SR VTX||180 mA||80 %||77 %||33 V||45 V|
Typ. ripple current at
Max. output voltage
cur-rent at full load
cur-rent at min. load
Max. non repetitive
output peak current at
output peak current at
|± 25 %||60 V||285 mA||265 mA||252 mA||349 mA|
Test result at 230 V, 50 Hz without dimmer connected.